BOTZ P70 PVC-U SOLVENT CEMENT

BOTZ P70 is a high-performance, fast-drying adhesive specially developed for pressure PVC-U piping systems and fittings. Its advanced formula does not contain harmful solvents such as Tetrahydrofuran (THF) and Cyclohexanone (CH), making it safer and more environmentally friendly compared to conventional PVC adhesives.The adhesive provides high bonding strength, resistance to pressures up to 16 bar, and long-term durability even under demanding operating conditions. BOTZ P70 ensures reliable and leak-proof joints in drinking water and wastewater systems, gas pipelines, industrial facilities, and agricultural irrigation networks.By combining safety, strength, and compliance with the international EN 14814 standard, BOTZ P70 is the trusted choice for professionals who value quality and long-lasting performance.


 

Features

• Solvent-safe formulation: free from harmful solvents (THF and Cyclohexanone)

• High pressure resistance (up to 16 bar)

• Effective for bonding both small and large diameter pipelines
 • Produced for bonding pressure PVC-U pipe systems and accessories according to BS EN 14814 and BS EN 14680 standards
 • Recommended for thermoplastic piping systems specified in BS EN 1452, BS EN 1455, BS EN 1566 and BS EN 1329
 • Suitable for non-pressurized PVC-U and ABS systems as well
 • Fast drying
 • High bonding strength and gap filling
 • Resistant to water, wastewater, gas and industrial fluids
 • Wide service temperature range (–25°C to +90°C)
 • Complies with EN 14814


Application Areas

• Bonding rigid PVC-U pressure pipes and fittings
 • Drinking water pipelines
 • Wastewater pipelines
 • Industrial pipelines
 • Gas distribution lines
 • Agricultural irrigation systems


 

Application 

• Pipe ends and joints must be cut at the right angle and deburred.
 • Adhesion surfaces must be cleaned beforehand.
 • Mark the surfaces where the adhesive will be applied. If wet, dry and clean from oil and dirt. Mix the adhesive before use and apply smoothly and evenly.
 • Apply the first coat inside the fitting and then along the pipe up to the marked area. For reliability, coat the pipe twice.
 • Insert the pipe into the fitting without turning. Hold for a few seconds until curing begins. Remove excess adhesive with a cloth.
 • Assembly must be completed within 3 minutes after application. At high temperatures and with thin layers, this time is shorter.
 • Do not apply pressure for the first 5 minutes. At temperatures below +10 °C, curing time increases 2–3 times.
 • Pressure tests can be carried out after 24 hours.


Important Notes

PVC-U bonding should be performed by trained personnel. Application forms recommended by pipe and fitting manufacturers should be followed.


 

Technical Information

Property

Value

Viscosity

2000–4000 mPas (Brookfield)

Density-Approximate

0.88 g/cm³

Open Time (1 mm film thickness)

1 min at +20°C / 30 sec at +40°C

Operating Pressure

up to 16 bar (EN 14814 compliant)

Service Temperature

–25°C to +90°C

Recommended Transport Temp.

+5°C to +30°C



Consumption

Pipe Inner Diameter (mm)

Pipe Outer Diameter (mm)

Consumption (gr)

25

32

8

32

40

11

40

50

15

50

63

17

65

75

22

80

90

40

100

110

80

125

140

130

150

160

190

200

225

260

250

280

380

300

315

520


 

Shelf Life: 
18 months in unopened package when stored in cool, dry conditions at temperatures between +5 °C and +25 °C.
 At temperatures below +5 °C, the adhesive may become more viscous and difficult to use. In such cases, bring the product back to room temperature and mix thoroughly until normal consistency is restored. 


 

Packaging: 

Metal Tin 500 gr (625 ml) - with brush

Metal Tin 1 kg (1250 ml) - with brush


Learn More

Related Products